Showing posts with label Wolseley Hornet. Show all posts
Showing posts with label Wolseley Hornet. Show all posts

Wolseley Spl Winter Work 2022 / 2023


Here is s short compilation of some of our work on the Wolseley Hornet over the winter months. We had hoped to have driven and tested the car in the autumn, but unfortunately when we came to put oil in the replacement gearbox, it poured out via the bell housing. At the same time a new crank and cam that had been on back order became available. This package will allow us to run a different firing order that seems to be more suitable for racing. And so it seemed to make sense to change the crank and cam whilst we attended to the gearbox problem instead of running the car with the standard firing order for the coming season and then changing over next year (as always planned). It is a bit trickier to change the crank without everything stripped off of the block, but it is still possible. Of course another new crank and cam is bound to raise some anomalies, we did have to make some cam bearings and readjust followers and make new securing dowels. The cam drive will be different which will require some alteration. At the same time we took the opportunity to complete some things off the "to do" list, including king pins and the making of two special oversize shackle pins...

What have we been up to through summer? Here is a brief photographic update!

 In the workshop:

1930s Wolseley Hornet Supercharged Spl. 

Here we have a few of the million and one little finishing jobs as this wonderful project comes to a close. Although, as with any racing car, it will never be complete as upgrades and modificaions are likely to continue for quite a while (we already have a major upgrade planned as we speak).

 I am afraid these are less interesting "general" photos, but we have a few items here that have been made through the early summer. These include the steering column dash bracket completion, dip switch provision including a bell housing mounted bracket, and some general some pipe work. A thrust assembly supplement for an aged and slightly damaged aux drive unit.  Pressure plate bolt alteration to clear the bell housing...yes it did just kiss when we turned the engine over by hand after fitting the grearbox. We had checked this in the early stages but, we have since obtained another gearbox and didn't think anymore of it until fitting the unit! You can see particular attention to maintaining equal bolt weight to maintain balance. 

Battery location and support. Fluid fills and wiring finishing, securing and general tidy. You wouldn't expect so much wire for a simple electric system! 

As always, most fittings are one offs in-keeping with the period, but very time consuming.




















1959 Turner 950 Chassis.

With the summer weather, it is nice to push the chassis out for work.
Most photos show suspension and chassis work. Some paint of bright areas may appear dull or dirty as we have Linseed oiled these to protect from our seaside air.
The gearbox and engine are only mock ups they are not the actual items. We have an A series  performance engine with Webers etc waiting in the wings.
We have wrapped the rear torsion bar in Waxoyl soaked hemp string to protect as this car will be used in all conditions.
These are early summer spring photos, more, up to date items will follow.





1946 Studebaker Champion
This is a more recent project, here we are preparing the engine for a full rebuild. Valve grinding is always a good initiation into the beginning of the build. Despite having been recut with new guides and valves, it is best to finish grind to be absolutely sure.
Here we are also removing pistons from rods, releasing the very clever self extracting cotter "wrist pin". Followed by a very thorough clean and brighten to inspect for any damage and to measure the alignment and the housing sizes ready for new bearings.
If these were for high speed or competition use, we would recommend crack testing, however for the type of work this engine will be doing these robust rods are unlikely to indicate any problems.
You can see in the photos that I have made a pair of Aluminium bungs that engage into a shoulder in the gudgeon pin to allow the piston assy to be firmly clamped without causing any load through the pistons or rods.







One cotter with damaged thread






Nose Art:
Something very unusual. I have been recreating the nose art on a very historic nose section of a Handley Page Victor K2. XL164 bomber / tanker aircraft. You can see the small sections of battered and faded paint that is the original, we are keeping that out of respect of her history, but we are reinstating by hand the totally missing areas including from the shoulders up!
It is said that five "Marham Bombers" were painted and named after each aircraft's chief engineer's wife or partner.
Saucy Sal can be seen at Bournemouth Aviation Museum http://www.aviation-museum.co.uk/ .

This is my biggest nose art project yet, it is very forgiving in this size.
The photos are a little distorted because of the barrel of the fuselage. She is more elegant in person!
Please click on them to see in a larger size.





Below: Prior to restoration of the nose art. Thank you to Bournemouth Aviation Museum for picture use.













An archive snapshot of our workshop about 5 years ago!


Turner Portrait Study

Looking forward to this one!











 


Thunderbird Tribsa


Nick's Hot Rod 32 Ford Birthday Cake!



Anthony's Lamborghini

Wolseley Hornet Cont'd


 Put to Bed For The Night ....If They Could Talk?...



Hornet Engine Preparation


Welcome to Jacob, Our New Apprentice, Mounting the Hornet Into An Engine Stand.





Cylinder Head Preparation.







Making Longer Outboard Aero Screen Posts


'59 Turner 950s Chassis Corroded Tube Replacement.










Turner Trailing Arm Replacement (Original in photo). The edges will be formed to a return and welded back to back, the teardrop section is an addition, as the originals had cracking adjacent to the large boss.


Richard has brought so many delightful, unusual cars on visits this year... thank you Richard and friends!





This wonderful Falcon has a Formula Ford 1600 Xflow engine..



And Below, Swanage Fire Service "Gumball Rally" after cakes of course..


Rebuilding Corroded Land Rover Defender Doors.









Alvis Grey Lady, Now running and waiting for delivery.



Grey Lady Distributor, we have machined a replacement distributor drive pin oversize and reamed the location to suit.

Air Silencer / Filter Housing Modified to Accept a Modern Peugeot Filter

The Original throttle Idle Horn had a very worn and a repaired post that was restricting smooth operation. We thought it best to ream the horn and make a new bush to suit, then to make a new post to allow smooth full operation.



In and around the workshop.


350 Bullet Royal Enfield Service.




New (Old) works truck, It is now Maroon and Cream with a black bonnet (see Jan 25th 2018 post) .... very Nascar!




A Few Small Wolesley Hornet Spl Jobs.

  Previously we made a wind deflector for the driver's Brookland screen, as with all things on this car, we tried to make it appropriate...